Service

Allt du behöver veta om din ljuddämpare inte fungerar som den ska.

Om din ljuddämpare behöver service eller om du upplever några problem med den, låt oss hjälpa dig.

Vi rekommenderar att du först utför egen felsökning. Om problemet kvarstår behöver du kontakta oss.

Tips! Du kan alltid rådfråga oss via telefon eller någon av våra återförsäljare innan du skapar ett ärende.

TROUBLESHOOTING

STEP 1

1. ARE THERE STAINS IN THE FRONT?

Do you have a mark on the muzzle? This may be because the silencer has come loose at some point during shooting. This is common at shooting ranges. Always check that the silencer is correctly mounted and securely fastened before starting shooting.

It sometimes happens during shooting at a shooting range that after a while, precision deteriorates. This is often due to the silencer coming loose as it heats up. If it is loose, you will get poor precision, and the bullet can leave a mark on the muzzle.

There is a function inside the silencer that should tighten it with each shot. Therefore, if it has come loose slightly, it can tighten again with the next shot.

STEP 2

2. THREADS

It's rare for a silencer that has performed well to suddenly shoot poorly.

Check if there is dirt in the threads. Also, consider if you may have accidentally bumped into the silencer and/or the firearm at some point, which could have caused the suppressor to be misaligned.

Learn more about how to clean and take care of your threads here >

STEP 3

3. POSITIONING BARREL SUPPORT

The barrel support is located at the rear edge of the suppressor and acts as an extra support for the suppressor. It should be 0.5-0.7 millimeters larger than the diameter of the barrel.

You should be able to easily move it with your fingers. If it is too tight, it will rest against the barrel and change the point of impact. It's important that the barrel support is used and that it is in the correct dimension.

If you were to get a blow to the silencer at the back or front end, the barrel support helps support the silencer against the barrel, so it doesn't risk becoming misaligned.

Manuals & Accessories

Important notes, instructions and product links — all Stalon accessory manuals in one place. Tap a product to open its info.

+

ACCESSORY MOUNT

Product

IMPORTANT NOTES:

Stalon Accessory mounts are perfect for attaching cameras, search lights, and other accessories. It is however important that the setup with weapon and silencer is tested for accuracy and point of impact.

INSTRUCTION:

Make sure that the Stalon accessory mount fits the model of silencer it is intended for. Install the accessory mount on the back-end of the silencer and attach the silencer with accessory mount mounted to the model it is intended for. Align the accessory mount to the correct position and secure it by clamping the weaver style base with a ring mount or similar. Test shoot the setup for accuracy and point of impact.

Read more about product ›
+

BARREL SUPPORT

Product
Barrel support

IMPORTANT NOTES:

Stalon barrel support is made of extremely heat-resistant composite. If the material deforms or melts, you have exceeded the silencer's maximum temperature limit. A melted barrel support can be replaced, and in some cases, the thread needs to be cleaned. Note that the barrel's temperature will be higher and affect the temperature the barrel support is exposed to. The Stalon barrel support should be adjusted to the diameter of the barrel, 0.5-0.7mm larger than the barrel's diameter. Accuracy will be negatively affected if the barrel bushing is in contact with the barrel.

INSTRUCTION:

Make sure that the Stalon barrel support fits the model of silencer and the diameter of the weapon barrel. Make sure to adjust the barrel support by milling or drilling the hole to the correct diameter (0,5-0,7mm larger than the barrel). This should be done by a professional person. Attach the barrel support by screwing it on to the back-end of the silencer. Check the barrel support to make sure it is not touching the barrel.

+

CONICAL BARREL SUPPORT

Product
Conical barrel support

IMPORTANT NOTES:

Stalon barrel support is made of extremely heat-resistant composite. If the material deforms or melts, you have exceeded the silencer's maximum temperature limit. A melted barrel support can be replaced, and in some cases, the thread needs to be cleaned. Note that the barrel's temperature will be higher and affect the temperature the barrel support is exposed to. The Stalon barrel support should be adjusted to the diameter of barrel, 0.5-0.7mm larger than the barrel's diameter. Accuracy will be negatively affected if the barrel bushing is in contact with the barrel.

INSTRUCTION:

Make sure that the Stalon Barrel support fits the model of silencer and the diameter of the weapon barrel. Make sure to adjust the barrel support by milling or drilling the hole to the correct diameter (0,5-0,7mm larger than the barrel). This should be done by a professional person. Attach the barrel support by screwing it on to the back-end of the silencer. Check the barrel support to make sure it is not touching the barrel.

+

FRONT-ENDS

Product

IMPORTANT NOTES:

None.

INSTRUCTION:

Make sure that the Stalon front-end fits the silencer it is intended for. Attach the Stalon front-end to the silencer by first removing the "original" front-end on the silencer. Test shoot the setup for accuracy and point of impact.

Front 108 › Front 149 › Front VR › Front VR-Venti ›
+

GAS REGULATOR H&K

Product
Gas regulator H&K

IMPORTANT NOTES:

Installation of a reator should only be carried out by an experienced- or professional person or gunsmith.

INSTRUCTION:

Installation of a gas regulator should only be carried out by an experienced- or professional person or gunsmith.

Read more about product ›
+

GASREGULATOR SAUER 303

Product
Gasregulator Sauer

IMPORTANT NOTES:

May not be mounted on a wooden stock. Contact us for mounting instructions.

INSTRUCTION:

Installation of a gas regulator should only be carried out by an experienced- or professional person or gunsmith.

Read more about product ›
+

MIMIC MUZZLE BRAKE

Product

IMPORTANT NOTES:

None.

INSTRUCTION:

Make sure that the Stalon MIMIC muzzle brake fits the weapon it is intended for. Attach the muzzle brake to the firearm firmly. Test shoot the setup for accuracy and point of impact.

Read more about product ›
+

MUZZLE BRAKE

Product

IMPORTANT NOTES:

None.

INSTRUCTION:

Make sure that the Stalon muzzle brake fits the weapon it is intended for. Attach the muzzle brake to the weapon firmly and, if necessary or wanted, screw in included adjustment screws for perfect recoil taking. Test shoot the setup for accuracy and point of impact.

Read more about product ›
+

NEOPRENE COVERS

Product

IMPORTANT NOTES:

Never use the Stalon neoprene cover over the recommended temperatur limit (250°C), Neoprene loses its elasticity at high temperatures.

INSTRUCTION:

Make sure that the Stalon neoprene cover fits the model of silencer it is intended for. Put the neoprene cover over the silencer and make sure it is covering the whole silencer. If the neoprene cover has a cordura reinforcement, make sure it is aligned on the top of the silencer when attached.

+

OPEN SIGHTS

Product

IMPORTANT NOTES:

Stalon pen sights fit most firearm/silencer combinations, it is however important that the combination is tested for accuracy and point of impact. The open sight stays perfectly aligned if attached correctly, even if the silencer is removed from the rifle and attached again.

INSTRUCTION:

Open sights X-series

Make sure that the Stalon open sight for X-series fits the model of silencer it is intended for. Install the open sight on the front-end of the silencer and attach the silencer with open sight mounted to the firearm it is intended for. Align the open sight with the sights on the firearm, secure the positioning of the open sight by screwing the locking bolt on the top of the open sight. Test shoot the setup and adjust sideways if needed.

INSTRUCTION:

Open sights VICTOR-series

Make sure that the Stalon open sight for VICTOR-series fits the model of silencer you have. Put the open sight on the back-end of the silencer and attach the silencer with open sight mounted to the firearm it is intended for. Align the open sight with the sights on the weapon, secure the positioning of the open sight by screwing the locking bolt on the underside of the open sight. Test shoot the setup and adjust sideways if needed.

+

SILENCER GREASE

Product

IMPORTANT NOTES:

For lubricating thread on the weapon and split section of some silencer.

INSTRUCTION:

Lubricate the thread on the weapon by applying Stalon silencer grease on the weapon thread. Lubricate the thread in the split section of some silencers by applying Stalon silencer grease on the thread.

Read more about product ›
+

THREAD ADAPTER

Product
Thread adapter

IMPORTANT NOTES:

Stalon thread adaptors should always be attached firmly to the weapon, not to the silencer.

INSTRUCTION:

Make sure that the Stalon thread adaptor fits the model of silencer and the thread on the weapon. Clean the thread on the weapon and apply Loctite, attach the thread adaptor firmly on the firearm and wait for the Loctite to harden. Attach the silencer to the thread adaptor and test shoot the setup to make sure the accuracy is perfect.

Read more about product ›
+

THREAD ADAPTER LONG

Product
Thread adapter long

IMPORTANT NOTES:

Stalon thread adaptors should always be attached firmly to the weapon, not to the silencer.

INSTRUCTION:

Make sure that the Stalon thread adaptor fits the model of silencer and the thread on the weapon. Clean the thread on the weapon and apply Loctite 243, attach the thread adaptor firmly on the firearm and wait for the Loctite to harden. Attach the silencer onto the installed thread adapter and check accuracy when shooting.

The barrel needs to be threaded according to our dimensions to ensure proper fit.

Read more about product ›
Download thread tolerance figure ›
+

THREAD COVERS

Product

IMPORTANT NOTES:

None.

INSTRUCTION:

Make sure that the Stalon thread cover fits the thread on the model it is intended for.

Read more about product ›
+

USER MANUAL

Download

DOWNLOAD PDF ›

MAINTENANCE & CARE - EXTENDED

Dry out silencer
step 1

DRY OUT

Always remove the silencer from the firearm when it is not in use. Allow the inside to dry if wet or damp. Use a heat gun, compressed air, hairdryer, fan, or similar until it is completely dry.

Clean the bore
step 2

CLEAN THE BORE

Start by cleaning the bore from any gunpowder residue. This is best done with a gun cleaning brass brush or boresnake.

Lubricate threads
step 3

LUBRICATE THREADS

Wipe the threads of the silencer with a piece of paper to remove any dirt. If dirt gets into the split section, it will cause problems when disassembling the silencer later. Lubricate the split section between the front and back parts (if the silencer is divisible). Use Stalon silencer grease >

Barrel's thread
step 4

BARRELS'S THREAD

Also lubricate the barrel threads with the same grease. Ensure that these are also cleaned from any debris.

Oil inside silencer
step 5

OIL

Finish by spraying a light gun oil for about 1-2 seconds (i.e., 1-2 short bursts) inside the silencer.

Store silencer
step 6

STORE

Store the silencer upright with the muzzle facing downward in a gun safe (or in another recommended way).

    Service & Support


    Beskriv ditt problem så tydligt som möjligt och bifoga foton om du kan.
    Vi granskar ditt ärende och återkommer med nästa steg.

















    Max 10 MB. Tydliga foton av framsida, baksida och eventuella skador hjälper oss att hjälpa dig snabbare.

    Stalon-garanti

    Tack för att du investerar i en Stalon-ljuddämpare

    Med varje ljuddämpare som levereras från Stalon följer en 6-årig garanti. Ett löfte om att om något under tillverkningsprocessen av din ljuddämpare skulle ha brustit, kommer vi att åtgärda och korrigera det. Om ljuddämparen däremot har skadats på grund av felaktig hantering, vårdslös användning eller bara av en olycka, kan garantin inte tillämpas för reparationer. Även om garantin inte gäller vill vi hjälpa dig, och naturligtvis till ett rimligt pris.

    *Service, reparationer och andra åtgärder kan endast utföras av Stalon AB eller av en Stalon-auktoriserad serviceverkstad.

    KONTAKTA OSS

    UPPLEV
    
PRECISIONEN HOS STALON
    SJÄLV

    HITTA ÅTERFÖRSÄLJARE